F00 — Basic functional group

code

Code name

setting range

value

attribute

F00.00

Motor 1 control mode

0: Speed sensorless vector control (SVC)

2: V/F control

2

〇

F00.01

Command source selection

0：Operation panel (LED off)

1：Terminal (LED on)

2：Com (LED flashing)

0

●

F00.02

Frequency source selection

0：Digital setting (no memory after power failure)

1：Digital setting (power failure memory)

2：AI1

3：AI2

4：Reserved

5：Pulse setting (X5)

6：Multi segment instruction

7：Simple PLC

8：PID

9：Communication given

1

〇

F00.03

Auxiliary frequency source selection

The same as F00.02

0

〇

F00.04

Selection of auxiliary frequency source range during stacking

0：Relative to maximum frequency

1：Relative to the main frequency command

0

●

F00.05

Range of auxiliary frequency source during stacking

0% ～ 150%

100%

●

F00.06

Frequency source selection

0: Main frequency source

1: Auxiliary frequency source

2: Main and auxiliary calculate results

3: Switching between main frequency source and auxiliary frequency source

4: Switching between main frequency source and main/auxiliary calculate results

5: Switching between auxiliary frequency source and main/auxiliary calculate results

0

●

F00.07

Choice of

main/auxiliary

0：main + auxiliary

1：main - auxiliary

2：the value bigger

3：the value smaller

0

●

F00.08

Set frequency

0.00Hz～max frequency

0.00Hz

●

F00.09

Main frequency source gain

0.0～300.0%

100.0%

●

F00.10

Auxiliary frequency source gain

0.0～300.0%

100.0%

●

F00.11

Main and auxiliary frequency calculate gain

0.0～300.0%

100.0%

●

F00.12

Synthetic frequency control

0：Synthetic output frequency

1: AI1*output frequency

2: AI2*output frequency

0

●

F00.13

direction

0：Same direction

1：opposite direction

0

●

F00.14

Acceleration and deceleration time reference frequency

0: Maximum frequency

1: Set frequency

2: 100Hz

0

〇

F00.15

Acceleration time 1

0.0s ～ 6500.0s

Mode

confirm

●

F00.16

Deceleration time 1

0.0s ～ 6500.0s

Mode

confirm

●

F00.17

Acceleration and deceleration time units

0：1 sec

1：0.1 sec

2：0.01 sec

1

〇

F00.18

Max frequency

50.00Hz ～ 500.00Hz

50.00Hz

〇

F00.19

Upper limit frequency

Lower limit ～Max frequency

50.00Hz

●

F00.20

Upper limit frequency

selection

0：F00.19 set

1：AI1

2：AI2

3：reserve

4：pulse set

5：communication give

0

〇

F00.21

Upper limit frequency bias

0.00Hz ～max frequency

0.00Hz

●

F00.22

Lower limit frequency

0.00Hz～upper limit frequency

0.00Hz

●

F00.23

carrier frequency

0.5kHz ～ 16.0kHz

机型确定

●

F00.24

Random carrier

0：no

1：yes

1

●

F00.25

Auxiliary frequency instruction bias during stacking

0.00HZ～max frequency

0.00Hz

●

F00.26

Frequency resolution

0: 1Hz

1: 0.1Hz

2: 0.01Hz

2

〇

F00.27

Digital setting frequency power off memory selection

0：NO Memory

1：Memory

1

●

F00.28

Motor parameter selection

0：Motor parameter group 1

1：Motor parameter group 2

0

〇

F00.29

operation frequency UP/DOWN

0：Operating frequency

1：Set frequency

1

〇

F00.30

Operation bundle main frequency instruction selection

Bit: Operation panel binding frequency source selection

Ten digit: Terminal binding frequency source selection

Hundred digits: Communication binding frequency source selection

0: Unbound

1: Digital frequency

2：AI1

3：AI2

4: Reserved

5: Pulse setting (X5)

6: Multi stage speed

7: Simple PLC

8：PID

9: Communication settings

000

●

F00.31

Modbus selection

0：MODBUS protocol

0

〇

F00.32

GP mode set

1：G mode

2：P mode

0

〇